Chamberlain 3595S Instrukcja Użytkownika

GARAGE DOOR OPENERModel 3595S 3/4 HPFor Residential UseInstall on Sectional Doors ONLYTHIS OPERATOR IS INTENDED FOR USE ONLY WITH I-BEAM RAILS.Owner’s

10Clevis Pin 5/16"x2-3/4"Ring FastenerINSTALLATION STEP 3Attach the Rail to the Header Bracket• Position the opener on the garage floor be

11INSTALLATION STEP 5Hang the OpenerThree representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1)

12INSTALLATION STEP 6Install the Door ControlLocate door control within sight of door, at a minimum height of 5' (1.5 m) where small children can

TrolleyNOTICEOverhandKnotEmergencyRelease HandleRopeTrolleyRelease Arm13INSTALLATION STEP 7Install the Light • Press the release tabs on both sides o

14INSTALLATION STEP 9Electrical RequirementsTo avoid installation difficulties, do not run the opener at this time.To reduce the risk of electric shoc

15Invisible Light BeamProtection AreaSafety Reversing Sensor6" (15 cm) max. above floorSafety Reversing Sensor6" (15 cm) max. above floorINS

16FLOOR MOUNT (RIGHT SIDE)WALL MOUNT (RIGHT SIDE)DOOR TRACK MOUNT (RIGHT SIDE)Indicator lightLensLip SensorBracketDoorTrackSensorBracketExtensionBrack

Invisible Light BeamProtection AreaSafety Reversing SensorSafety Reversing SensorConnect Wire toOpener Quick-Connect TerminalsBell WireBell WireFinish

18Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacture

19INSTALLATION STEP 12Connect Door Arm to TrolleySECTIONAL DOORS ONLY• Make sure garage door is fully closed. Pull the emergency release handle to di

INTRODUCTIONSafety Symbol and Signal Word ReviewThis garage door opener has been designed and tested to offer safe service provided it is installed, o

20ADJUSTMENT STEP 1Adjust the UP and DOWN Travel LimitsLimit adjustment settings regulate the points at which the door will stop when moving up or dow

21ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the right side panel of the motor unit. Force adjustment settings regulate

22Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage

OPERATION 23IMPORTANT SAFETY INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:WARNINGWARNINGWARNINGWARNING1. READ AND FOLLOW ALL WARNINGS AND

24Using the Wall-Mounted Door ControlTHE SMART CONTROL PANEL™Press the push bar to open or close the door. Press again to reverse the door during the

TroubleshootingReduced proximity sensing (does not activate by touching top of remote control)Check if proximity lighting is disabled by pressing a bu

CARE OF YOUR GARAGE DOOR OPENERLIMIT AND FORCE ADJUSTMENTS:Weather conditions may cause some minor changes in door operation requiring some readjustme

Having a Problem? (Continued)5. Opener noise is disturbing in living quarters of home:• If operational noise is a problem because of proximity of th

Meaning: This message will appear if the Safety Reversing Sensors are out of alignment, if they are blocked or if the wiring is disconnected. To clear

To Add or Reprogram a Hand-held Remote ControlUSING THE “LEARN” BUTTON USING THE SMART CONTROL PANEL™29PROGRAMMING*3-Button RemotesIf provided with y

3To prevent damage to garage door and opener:• ALWAYS disable locks BEFORE installing and operating the opener. • ONLY operate garage door opener at

301. Press and release the “learn” button on motor unit. The learn indicator light will glow steadily for 30 seconds.2. Within 30 seconds, enter a f

31811126NOTICEUPCEILING MOUNT ONLY971013143421LOCKLIGHT5134 652REPAIR PARTSRail Assembly PartsKEY PART NO. NO. DESCRIPTION1 4A1008 Master link ki

Motor Unit Assembly Parts32DNDNUPUPBrownWire(Down)ContactLIMIT SWITCH ASSY. GreyWireYellowWire(Up)ContactCenter LimitContactDriveGear3 5 4 2 1 16 20 9

CLOSEDOPEN33LOCKLIGHTACCESSORIES 915LM1702LM Outside Quick Release:Required for a garage with NO access door. Enables homeowner to open garage door ma

34NOTES

35NOTES

©2008, The Chamberlain Group, Inc.114A3617 All Rights Reserved LIFTMASTER® SERVICE IS ON CALLOUR LARGE SERVICE ORGANIZATION SPANS AMERICAINSTALLATI

Safety Reversing SensorSupport bracket & fastening hardwareis required.See page 11. — — — — — — — —Header WallFINISHED CEILINGTorsio

5UPCEILING MOUNT ONLYChassis SupportBracketChain SpreaderExtensionBracket (2)RailChain Pulley BracketChainStraight DoorArm SectionCurved Door Arm Sect

Washered Bolt 5/16"-18x1/2"Lock Nut6ASSEMBLY STEP 1Attach the Rail to the Motor UnitTo avoid installation difficulties, do not run the garag

7ASSEMBLY STEP 4Tighten the Chain• Spin the inner nut and lock washer down the threaded shaft, away from the trolley.• To tighten the chain, turn ou

8INSTALLATION STEP 1Determine the Header Bracket LocationSECTIONAL DOOR ONLY1. Close the door and mark the inside vertical centerline of the garage

9INSTALLATION STEP 2Install the Header BracketYou can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow th